Your cart is empty

APEX Python MOSFET - V3 Drop In 34 Amp Polyfused


These MOSFETs were developed through a joint partnership between Clandestine Airsoft and Apex Electrix LLC. They are designed to outperform all other MOSFETs by using the most advanced semi-conductor technology allowing for super low resistance operation and ultra fast switching times. These combined allow the maximum current capacity and maximum power increase to the motor. Unlike most simple MOSFETs these have dual transient voltage suppressors (TVS) to protect the FETs from high voltage spikes caused by static buildup and motor inductance. They have a 5KW primary TVS to protect from motor spikes and a 600W secondary for static shocks from the trigger.

Mosfets serve two main purposes in airsoft guns. One is to take the load off the trigger contacts and use a solid state ultra powerful MOSFET to switch power to the motor instead. This means that the trigger contacts will no longer wear as they are only seeing a very small amount of current. Besides not wearing out trigger contacts a MOSFET will often increase rate of fire due to the lower resistance of the FET and new wire. The Python FET has been designed with ultra low resistance in mind to maximize the power increase to the motor and increase ROF. Using a MOSFET is very important if you're using high powered batteries like 11.1V Lipo or high discharge 7.4V LiPos as without one your trigger contacts will very quickly be worn away by the high current arcs.

The real world amount of current a MOSFET can carry is based on it's temperature, which is based on the amount of power it needs to dissipate. This power is generated from the resistance of the FET during operation. The two key resistances in FETs are the on resistance and the resistance that happens when the FET is between off and on. Keeping the on resistance as low as possible and the switching time as fast as possible reduces the total average resistance. By reducing the total average resistance the power wasted in the FET that ends up as heat buildup is reduced. This thermal failure happens long before the theoretical maximum FET current ratings so reducing the on resistance and switching time is more important that the max current ratings. PCB based FETs also have more surface area for the FET dissipate heat into.

FET Comparison

On Resistance

Pulsed Max Current

Max Current Rating

Max Power Rating

Switch Time



















PCB based MOSFETs like these also have the added advantage of higher durability due to their ridged fiberglass reinforced substrate that prevents pins and lead from snapping off the delicate components. Like most FETs these are covered in heat shrink to protect their internals. The low resistance 16 ga wires on these FETs are all Teflon insulated which offers superior abrasion and temperature resistant for ease of wiring in tight spaces and extreme current conditions.

These V3 drop in FETs are designed to put installed in version 3 replicas without any soldering. They have a SHS trigger, Lonex Gold motor connectors and XT Deans connectors already installed. If your batteries have deans on them already you can just plug and play in no time. These also come with one female deans connector to attach to your existing battery if it's not equipped with deans.

While these are designed to be as universal as possible, there are many different types of guns that may require more or less wiring than provided.  They are designed to fit normal AKs but may fit other configurations as well.  We give no guarantee that it fits any particular replica.

Max Recommended Battery Voltage: 14.8V Lipo
Max Power Rating: 544 Watts
Wire Type: 16 ga Teflon / 22 ga Teflon
FET Resistance: 0.375mOhm
Voltage Spike Protected : 5000Watt primary and 600Watt secondary
PCB Based
Fuse: 34A polyfuse

Sold Out

To be notified when this product is back in stock please click here.

  • Model: Python-V3-PTC
  • Shipping Weight: 0.1107lbs
  • 0 Units in Stock
  • Manufactured by: Apex Electrix LLC

Current Reviews: 1

This product was added to our catalog on Thursday 30 October, 2014.

Let us notify you when this product is back in stock!

Simply enter your details below and we will send you an e-mail when “APEX Python MOSFET - V3 Drop In 34 Amp Polyfused” is back in stock!

We will not send you any other e-mails or add you to our newsletter, you will only be e-mailed about this product!